Garage ceiling with a hexagon LED grid beside a standard linear LED fixture and a door opener rail

Hexagon Lights vs Shop Lights and High Bays: Which Suits Your Workshop?

The short answer

It depends on the ceiling and the work. Under about 13 ft, or anywhere you can hang a grid closer to the work, a hexagon grid gives softer shadows and more even light across the shop than a few LED shop lights, and you replace a single tube instead of a fixture. LED shop lights are the budget pick for plain floors, and high bays suit tall steel buildings. Per watt, the three are closer than most people expect, so compare lm/W on the spec sheets.

In this guide

Most shops start with a few 4 ft LED shop lights hung on chains, while bigger buildings with tall ceilings tend to use high bays instead. A hexagon grid is the newer option, and it usually costs more up front, so the fair question is what you get for the difference.

We sell hexagon grids, so read this as a seller's comparison with the trade-offs left in. It is written for home shop owners and small commercial shops choosing ceiling lights, and it leaves task lights aside. If you're already leaning toward a grid, our range of hexagon shop lights for precision work shows the kits.

Three Ways to Light a Shop

  • LED shop lights. Linear fixtures, usually 4 ft long, hung on chains or mounted to the ceiling in rows, which makes them cheap per fixture and quick to add as the shop grows.
  • High bays. Compact, high-output fixtures, round (often sold as UFO lights) or linear, built for tall ceilings in warehouses, gyms and big shops.
  • Hexagon grids. One connected fixture of LED tubes in a honeycomb pattern, spread across a large part of the ceiling.

Our team has spent over 13 years in the lighting industry, and in that time we have learned to judge any shop fixture on the same six points: shadows, evenness, glare, ceiling height, upkeep and cost. Brightness matters as well, and our best workshop lighting guide covers how much each type of shop needs.

Side by Side

Shop test Hexagon grid LED shop lights High bays
Shadows at the bench Soft, filled in from many tubes Softer with more rows, harder between them Hard under each fixture unless you add many
Evenness across the floor Even under the grid's footprint Bright under each row, dimmer between rows Bright pools at low heights, better in tall buildings
Glare looking up Low-glare diffuser on HEXLED tubes Varies by lens A compact, very bright source, so check the lens
Best ceiling height Surface mount up to about 13 ft, hang it lower on cables above that Low to mid ceilings Tall ceilings
When something fails Swap one tube, the rest stay lit Integrated fixtures are usually replaced whole Usually replaced as a fixture
Upfront cost Usually the highest for the same floor Lowest Depends on the model and the count
Look A finished, designed ceiling Utilitarian Industrial

Shadows, Evenness and Glare

A shadow's edge depends on how big the light source looks from where you stand. A compact high bay is a small, intense source, so it draws sharp shadows, while a row of shop lights is longer and softer along its length but still leaves dimmer bands between the rows. A grid puts light lines across the ceiling, so the shadow of your head or hand is filled in from other directions.

That is the main thing you pay for with a grid. Brightness is cheap. Light that reaches the bench from every side is harder to get with a few fixtures.

Glare is the other half. HEXLED tubes sit behind a low-glare diffuser. With a high bay, look at the lens, because a compact source that bright is hard to look at when you're on a creeper looking up.

This fall a customer planning a 17 by 25 ft bay with a 12 ft ceiling asked us to run three 8 ft LED fixtures from another brand in line with a hex grid. HEXLED connectors only fit HEXLED tubes, so those fixtures could share the ceiling but not join the grid. The layout we sent ran one grid along most of the bay's length.

Hexagon LED grid spread across a shop ceiling between rows of older fluorescent tube fixtures
A hexagon grid sharing a shop ceiling with long fluorescent tubes. Each tube lights a band, while the grid spreads across the ceiling around them.

Ceiling Height Decides a Lot

High bays exist for tall buildings. Their output and optics are designed to throw light down from well above the floor, which is why they suit warehouses and big clear-span shops.

A grid surface mounts on ceilings up to about 13 ft, and above that it hangs on suspension cables in 3.3 ft and 9.8 ft lengths, which brings it down toward the work. In a very tall building, where even long cables leave the grid far above the floor, high bays are usually the simpler answer. Another option is a grid hung over the main work zone with high bays lighting the rest.

Round high bay lights hanging from a tall arched steel roof in a large industrial hall
High bays under a tall steel roof, the kind of building they are made for.

Dust, Repairs and Warranty

Every HEXLED tube runs on its own driver, so if one fails, the rest of the grid stays lit and you swap just that tube with the removal tool from the box. Replacement tubes come in 5-packs matched to your kit.

With integrated LED shop lights and most high bays, a failure usually means replacing the whole fixture, which is cheap for a shop light and more of a job for a high bay hung 20 ft up.

Dust settles on everything in a shop. HEXLED tubes are rated IP54, dust and splash resistant, and the smooth tubes wipe clean with the power off. White HEXLED kits carry a 4-year warranty for home use and 2 years for commercial use.

Are Hexagon Lights More Efficient Than LED Shop Lights?

Not necessarily. Efficiency is measured as luminous efficacy, the lumens a fixture puts out for each watt it draws (lm/W). HEXLED tubes run at 110 to 120 lm/W. Many LED shop lights and high bays publish figures in a similar range, and some list higher numbers, so compare the spec sheets rather than the shape.

What a grid changes is how the light is spread, not how much you get per watt.

Cost: What the Difference Buys

Per fixture, LED shop lights are the cheapest way to add light, and a hexagon grid usually costs the most to cover the same floor. High bays sit in between, depending on the model and how many you need.

The extra buys light from more directions, a ceiling that looks finished and repairs at the tube level. For storage or parking, that may not be worth paying for. For a bench where you spend your weekends, or a bay that customers walk through, it usually is.

To compare fairly, work out how much light your floor needs first. Our lumens calculator gives you a target, and then you can price each option against that target instead of by fixture count.

Can You Mix Them?

Yes, and plenty of shops should. Put the grid over the bench, the lift or the layout table, and use shop lights over storage shelves and the parking end of the room. In a tall building, a grid hung over one work zone with high bays elsewhere works too.

Match the color temperature across all of them, or the room looks patchy. HEXLED color temperature is fixed when you order, in 3000K, 4000K, 5000K or 6500K, so check what your other fixtures use before you buy.

Which One Fits Your Shop

  • Home garage shop under about 13 ft, with work spread around the room: a hexagon grid.
  • Storage, parking or a plain floor on a tight budget: LED shop lights.
  • Tall steel building with a clear span: high bays, with a hung grid over the main work zone if you want one.
  • Detailing, paint or finish work: a grid, for even light and less glare along the panels.

Still deciding whether a grid suits your kind of shop? Start with whether hexagon lights suit your shop. Ready to plan the ceiling? Our guide to installing hexagon lights in a workshop covers mounting and power. Once you've settled on a grid, compare kits in our honeycomb shop lighting range.

About this article, . It compares a hexagon grid with LED shop lights and high bays for workshops. HEXLED specs come from our product pages and installation guide, and other fixtures are described in general terms, so check their spec sheets.

Frequently Asked Questions

Are hexagon lights better than LED shop lights for a workshop?

For a shop under about 13 ft where the work is spread around the room, usually yes. A grid fills in shadows from many directions and lets you replace a single tube. Shop lights cost less and suit storage or parking areas.

Are LED hex lights more efficient than regular LED shop lights?

Not necessarily. HEXLED tubes run at 110 to 120 lm/W, and many LED shop lights publish figures in a similar range. A grid changes how the light is spread, not how much you get per watt.

When are high bays a better choice than hexagon lights?

In tall buildings where even 9.8 ft suspension cables would leave a grid far above the floor. High bays are built to throw light down from height.

Can I mix hexagon lights with shop lights in the same shop?

Yes. Put the grid over the main work area and shop lights over storage, and match the color temperature. HEXLED connectors only fit HEXLED tubes, so other fixtures need their own mounting and power.

Are hexagon lights harder to maintain than shop lights?

No. Each tube has its own driver, so one failure leaves the rest lit, and you swap that tube with the removal tool. Wipe the tubes with the power off to clear shop dust.