Bordered hexagon LED grid assembled and lit on a garage floor before it is mounted overhead

Installing Hexagon Lights in a Workshop: Ceilings, Height and Power

The short answer

Plan the grid around the shop first, including the overhead door in its open position, the opener rail, lift posts, heaters and the bench. Then mount by ceiling type. Flat drywall or wood up to about 13 ft takes an anchor and screw at each mounting point, a drop ceiling takes zip ties on its metal grid, and open trusses, sloped ceilings or tall metal roofs call for suspension cables. Smaller non-dimmable kits plug into a grounded outlet, while larger kits and all dimmable kits are connected by a licensed electrician.

In this guide

A workshop ceiling is busier than a living room ceiling. There is a garage door that rolls up under it, an opener rail, maybe a lift, a heater, a dust collector duct and a run of air line. A hexagon grid has to fit around all of it.

This guide is for shop owners and the installers and electricians they work with. It covers the decisions that are specific to a shop: where the grid goes, how it attaches to your kind of ceiling, and how it gets power. It assumes you have already picked a kit from our workshop hex lighting range, or are close to it.

Plan the Layout Around the Shop, Not the Ceiling

Sketch the shop from above before you think about screws. Mark the walls, the ceiling height and anything that hangs or moves overhead.

  • The overhead door in its open position. A sectional door rolls back under the ceiling and can reach several feet into the room.
  • The opener and its rail. The rail hangs below the ceiling. Decide whether the grid runs beside it or around it, and leave room to service the opener.
  • Lifts. A raised vehicle comes close to the ceiling. Any grid, flush or hanging, has to stay above the highest point the lift and your tallest vehicle reach.
  • Heaters, fans, ducts and sprinkler heads. Give each one the clearance its maker asks for.
  • Power. Note the nearest outlet and where an electrician could run a feed. Our guide to plug-in vs hardwired garage lights explains both routes.
  • The work zones. Mark the bench, the machines and the layout table. Those spots need the light most.

When our team drew shop drawings for a customer's two garages this fall, we marked the area the open door sweeps, numbered every mounting point and listed its position from the walls, so the installer could mark the ceiling straight from the sheet. On one of the two, the power inputs went on the side away from the door. Leave a few inches of margin around the grid as well, because tube lengths are nominal and the connectors add a little to the overall size.

Can I arrange the hexagons in any pattern I want?

Within a kit, the tubes and connectors go together in the honeycomb pattern shown in the manual, and each power input connector sits on the outer edge of the layout. If your shop needs a different shape, such as a long strip down one bay or two grids on either side of a roof ridge, our team can draw a custom layout for your shop and supply the connectors to match. One limit to know up front: HEXLED connectors only fit HEXLED tubes, so tubes or LED fixtures from other brands can't join the grid.

Mounting by Ceiling Type

The mounting points are the connectors at the corners of the honeycomb. How they attach depends on what is overhead. Our guide on how to install hexagon lights shows each method step by step. Here is how they line up with common shop ceilings.

Ceiling How the grid attaches Watch for
Drywall, plywood or OSB up to about 13 ft An anchor and screw at each mounting point Leave a few inches of margin around the grid
Open joists or trusses Suspension cables from the framing, one per mounting point Keep the grid level wherever the framing falls
Scissor trusses or a sloped ceiling Each grid on one slope, or hung level on cables A flat grid can't bend over the ridge
Metal building Fixed to the purlins, or hung from them on cables Thin panels and ribs rarely line up with the mounting points
Drop ceiling Zip ties on the metal ceiling grid Zip ties aren't included
Wall An anchor and screw at each mounting point Useful over a bench when the ceiling is out of reach
Anything above about 13 ft Suspension cables in 3.3 ft or 9.8 ft lengths Clear the open door, the opener and a raised vehicle

Drywall, plywood or OSB up to about 13 ft

Flat, finished ceilings are the simple case. The kit includes a plastic anchor and screw for every mounting point, and once it is up the system sits under 1.6 in from the ceiling. A finished garage shop usually falls here.

Open joists and trusses

With no flat surface, the mounting points rarely land on a joist or a truss chord. Hang the grid from the framing on suspension cables instead, one cable per mounting point, so the honeycomb stays level wherever the framing falls. Mounting on a wall is the other option.

Scissor trusses and sloped ceilings

A grid is flat. Surface mounted, it can't bend over a roof peak, so each system has to sit on one slope or hang level below it on cables. This fall our team laid out a 38 ft by 26 ft 6 in garage with a scissor-truss ceiling, 13 ft at the ridge, as two long custom systems, one on each side of the ridge.

Metal buildings with purlins and corrugated panels

In a steel shop or a pole barn, the roof panels are thin and their ribs rarely line up with the mounting points. Fix to the purlins, the horizontal members that carry the roof, or hang the grid from them on cables. Ask your installer which fasteners suit your framing.

Hexagon LED grid mounted across a black corrugated metal shop ceiling with a ladder below
A full grid across a corrugated metal ceiling. In a metal building, what the mounting points fix to matters more than the panels.

Drop ceilings in a shop office or showroom

Don't drill the tiles. Secure the system to the metal ceiling grid with zip ties instead. Zip ties aren't included, so pick up a pack before install day.

Walls

A grid mounts on a wall the same way as on a flat ceiling, with an anchor and screw at each mounting point. A wall grid over a bench is one answer when the ceiling is out of reach.

Ceiling Height: Surface Mount or Hang It

Up to about 13 ft, surface mount the grid. Above that, hang it. Our adjustable suspension kit, sold separately, uses steel cables in 3.3 ft and 9.8 ft lengths (1 m and 3 m), and the cables attach at the same mounting points the screws would use. Plan on one cable per mounting point.

Hanging height is a balance. Lower brings the light closer to the work, but the grid still has to clear the open door, the opener and a raised vehicle. For how mounting height changes the light level at the bench, see our best workshop lighting guide.

For a barbershop with a long floor and a high industrial ceiling, our team designed a custom system about 33 ft long and hung it on 9.8 ft cables. The light came down to the stations instead of disappearing into the rafters, and the same idea works over a bench in a tall shop.

Two small hexagon light clusters under a steel-beam metal roof in an empty garage shop
Two small clusters under a steel-framed metal roof.

Power: Plug-In or Hardwired

How a kit gets power decides whether you need an electrician.

  • Smaller non-dimmable kits ship with a plug-in power cord. Mount the grid, then plug it into a grounded outlet.
  • Larger kits ship with a hardwire cable for each power input, and some have two or three inputs. Have a licensed electrician connect them.
  • All dimmable kits are hardwired to a wall switch by a licensed electrician. The switch steps the grid through 100%, 60% and 30%, and they are not made for dimmer sliders or smart switches.

Mark where each power input will land before anything goes up, since the inputs sit on the outer edge of the layout. Put them near the outlet or the spot your electrician plans to feed, not behind a lift or in the path of the door.

Splitting a Shop Into Zones

One big grid is not the only option. Two or three smaller grids let you light the bench end and the bay end separately, steer around a lift or a roof ridge, and switch off the part of the shop you aren't using.

Each grid has its own power input or inputs. With plug-in kits, that can simply mean separate outlets. With hardwired kits, a licensed electrician can put each grid on its own wall switch. A dimmable grid over a mixed-use area helps too, with full output for a brake job and 30% when the room is just a garage again.

Lay It Out on the Floor First

Assemble the grid on a clean floor or a tarp before anything goes overhead. You see the shape at full size, you can check it against the marks on the ceiling, and you find a missing connector while it is still easy to fix. Then test it. With a plug-in kit, plug it in for a moment and check that every tube lights. For a hardwired kit, have your electrician handle the test. Reseating a tube at floor level takes seconds, and on a ladder it takes much longer.

Plan for Upkeep

Every tube runs on its own driver, so one failed tube doesn't take the rest of the grid down. You swap only that tube, using the red removal tool from the box to release the snap-lock latch. Replacement tubes come in 5-packs matched to your kit, in the same color temperature and version.

Shop dust settles on the tubes over time. Wipe them with the power off when you clean the shop, and keep a clear path for a ladder under the grid rather than a permanent shelf in the way.

Next Steps

  1. Sketch the shop from above with the door, opener, lift, heaters and work zones marked.
  2. Match each part of the ceiling to a mounting method, and check the height against the 13 ft line.
  3. Decide plug-in or hardwired, mark the power inputs, and book a licensed electrician if you need one.

Want a second pair of eyes on the sketch? Send it to the HEXLED team. If you are still deciding whether hexagon lights suit your shop, or how they stack up in our comparison of hexagon lights vs shop lights and high bays, start there. When the plan is ready, compare kits for your workshop ceiling light solution.

About this article, . It covers planning, mounting and power for a hexagon grid in a workshop. Mounting methods, cable lengths and power details come from our installation guide and product pages.

Frequently Asked Questions

Do I need an electrician to install hexagon lights in a workshop?

Not for a smaller non-dimmable kit, which plugs into a grounded outlet. Larger kits and all dimmable kits ship with hardwire cables, so have a licensed electrician connect them.

How high can I surface-mount hexagon lights?

Up to about 13 ft. Above that, hang the grid on suspension cables, which come in 3.3 ft and 9.8 ft lengths and attach at the same mounting points as the screws.

Can I install hexagon lights on exposed joists or trusses?

Yes. Hang the grid from the joists or the truss chords on suspension cables, one per mounting point, so it stays level wherever the framing falls. A wall is the other option.

Can I arrange hexagon lights in any pattern I choose?

A kit follows the honeycomb pattern in its manual. For another shape, such as a long strip or a layout that works around a lift, our team can draw a custom layout and supply the matching connectors.

Can I connect other LED shop lights to a hexagon grid?

No. HEXLED connectors only fit HEXLED tubes. Other fixtures can share the ceiling, but they need their own mounting and power.

Can different parts of the shop be on separate switches?

Yes, if you plan the shop as two or more grids. Each grid has its own power input, so a licensed electrician can put each hardwired grid on its own switch, and plug-in kits can use separate outlets.